TIGER OPTICS Prismatic 3 laser-based, multi-species trace gas analyzer

This compact, CRDS-based analyzer for the detection of H₂O, CO, CO₂ and CH₄ from parts-per-billion to parts-per-million levels to ensure purity requirements in line with SAE J2719 and ISO 14687:2019.

Prismatic 3 is easy to install and operate with integrated touchscreen and intuitive graphical user interface to allow efficient data trending and analysis. The cost of ownership is extremely low, with no calibration, spare parts or utility gases required.

The Prismatic 3 features:

• Simultaneous parts-per-billion detection of CO, CO₂, H₂O and CH₄
• Ideal analyzer to meet Hydrogen purity requirements of SAE J2719 and ISO 14687:2019
• Powerful Cavity Ring-Down Spectroscopy (CRDS) technology
• Low Cost of Ownership: no calibration or utility gas requirements
• Easy to install and use per ASTM Standard Test Method D7941

Applications

• Air Separation Units & Nitrogen Plants
• Gas Quality Control
• Gaseous CRMs & Calibration Gas Mixtures
• Greenhouse Gas Monitoring
• High-Purity Gases & Systems
• Hydrogen Fuel Cells
• Research & Development

Data Sheet

The post Prismatic 3 appeared first on Thomson Environmental Systems.

Since the M&C dilution probe SP2000-H/DIL is based on the well-proven M&C gas sample probe SP2000H, a variety of applications requiring special filter techniques, materials, etc. can be handled without any problems with this dilution probe.

Gas sample dilution probe type SP2000‑H/DIL features:

• external ceramic filter type S‑2K150
• filter porosity: 2 µm
• electrically heated external filter from 0 to 180 °C, adjustable by an integrated thermostat
• high‑temperature limiter with reset key responding at +30 °C above Tset and low‑temperature alarm with potential‑free status‑alarm contact at ‑30 °C below Tset,
• incl. weather protection shield with insulation
• power: 230 V/50 Hz, 800 W
• mounting flange: DN 65 PN 6B with G 3/4″ f connection
• sample gas OUT: 8‑mm‑tube
• material: SS 316Ti, ceramic, Viton®
• Dilution ratio to be indicated with the order

Gas Sample Dilution Probe SP2000-H/DIL brochure

The post Gas Sample Dilution Probe SP2000-H/DIL appeared first on Thomson Environmental Systems.

Gas Sample Probe SP4000-H brochure

The post Portable Gas Sample Probe PSP4000-H appeared first on Thomson Environmental Systems.

Gas Sample Probe Series SP®Versions SP2000, SP2000-H, SP2300-H, SP2400-H range brochure

The post Gas Sample Probe SP2000-H appeared first on Thomson Environmental Systems.

Speed and Small footprint

With analytical cycles 10 to 50 times faster than traditional chromatographs, the Falcon Series Ultrafast Gas Chromatograph (GC) vastly increases responsiveness for the data consumer in a wide range of lab, process and field applications. Less time spent waiting on results means more productivity and timely control of measured processes. Product output, quality and profitability are increased while field analysis becomes more practical and reliable.​

The Falcon Series GC’s incredible speed inspired a new Ultrafast Simulated Distillation Method. The ASTM D7798 method can perform simulated distillation nearly 6 times faster than the previous method (D2887), with superior repeatability and reproducibility.

The elimination of the air bath column ovens, required for traditional gas chromatography, reduces the Falcon Series GC footprint. Yet the Falcon Series delivers all the functionality of much larger, higher thermal mass, traditional GCs. At 43 cm wide, 22 cm deep, 28 cm high and 11 kg, the Falcon Series offers advanced analytical chemistry in a highly compact, versatile package.​

The smaller size of the Falcon Series GC means more efficient utilization of space and, ultimately, bigger profits for the user. The small Falcon Series footprint allows for higher installation density in the laboratory and enables process installation schemes that place the analyzer much closer to its sampling point in the plant. Closer proximity means less sample lag time as well as more representative measurements for process control. This also makes hand carried and vehicular transport applications far more feasible.​

Smarter

Using modern computing with standard operating systems and software, the Falcon Series GC frees valuable technical resources from the daily grind of interpreting and validating chromatographic results. State-of-the-art Chromperfect® GC operating software is built in and LineUp software virtually eliminates misidentification of components and drastically reduces the need for expensive calibration sample runs. Less time spent calibrating the analyzer means more time spent on more economically valuable diagnostics, most notably measured process deviations from the set-point. In addition to Chromperfect®, Infometrix Pirouette® is an optional software that may be added to enable interface with process automation.​

Easier

Teledyne’s patented direct heating of the temperature-programmed column modules allow the Falcon Series GC to avoid the complicated and troublesome valve schemes used in isothermal process analyzers and many lab gas chromatographs. The Falcon Series GC’s patented overall modular design also makes diverse application engineering and maintenance easier, as column and detector modules are readily changed out as needed.​

Correlation between laboratory systems and online process control systems become realistically possible with the Falcon Series system, because both physical packages use the same measurement principle, hardware and methodology. Applying the Falcon Series GC in-lab and online means less time spent reconciling lab and process measurements and validating which result is correct. More time can be spent working on valuable, direct process optimization.

Greener

Whether in the control laboratory, online in the processing plant, near line in the pilot plant or when transported for field measurements, by consuming less than 300 Watts in operation, the Falcon Series GC uses about 1/10th of the power of traditional GCs.​

With analytical cycles that are many times faster and the low electrical load needed for operation, the Falcon Series GC’s power consumption per analysis is 1% or less of the energy required by traditional gas chromatography. Combine these savings with the reduction in workload for air conditioning systems and the Falcon Series solution is greener still. The Falcon Series product life cycle environmental impact from manufacturing throughout its useful lifetime to disposal is far less than traditional GCs.

The Result​

Faster, Smaller, Smarter, Easier, Greener = better quality, increased productivity, profitability and versatility, with far less hassle and environmental impact. That summarizes the business concept for the ultrafast, compact, ultra-user friendly, energy efficient, highly durable, practical, reliable and economical Falcon Series Ultrafast Gas Chromatograph.​

Falcon GC Brochure

The post Teledyne Falcon Ultrafast Gas Chromatograph appeared first on Thomson Environmental Systems.

For stack testing and emissions monitoring, time is the most important resource; GT6000 Mobilis helps you save it.
Extreme portability, easy setup, fast results – the Gasmet GT6000 Mobilis portable FTIR multi-Component stack gas and emission analyzer is designed for Stack Monitoring with a list of features to make you more efficient.

Key benefits include:

• The first and only FTIR analyzer with MCERTS EN15267-4 certification
• Intuitive user interface and ergonomic design
• Easy to disassemble, carry, and set-up again
• Multigas measurements in a portable package
• Realtime results reliably and remotely
• Exceptional robustness: shock and vibration resistivity by design
• Smart software with self-diagnostics for easy and fast service
• Suitable for on site or laboratory use.

GT6000 Mobilis Data Sheet
GT6000 Mobilis Brochure

GT6000 Mobilis is designed to be used with the portable sampling system, PSS Plus or PSS Base. PSS utilizes the hot-and-wet measurement principle (no drying or dilution), which ensures that the analysis is done with a representative sample. There is two-stage particulate filtration: the first one in the sampling probe and the second one in the sampling system. The portable sampling system can be optionally equipped with a ZrO2 sensor for accurate oxygen measurement.

With all-new design the user experience has been taken to new heights. Integrated controls on front, 2 handles and cables in the back provide smooth operation. While PSS Base offers more basic design, for more hardcore work we have PSS Plus. PSS Plus comes with flow meters on front and has an instrument air option. This makes the system easier and cheaper for user while also providing safer operation, since nitrogen is only needed for background measurements.

PSS Data Sheet

The post GASMET GT6000 Mobilis appeared first on Thomson Environmental Systems.

Ideal for monitoring air quality outside or in workshops, TES Small Form AQMS measures key parameters:

Air pollutant concentrations: PM₁, PM_2.5, PM₄, PM₁₀, TSP, O₃, NO, NO₂, O3, CO, SO₂, H₂S, NH₃, HCHO, Cl₂, HCl, VOC, CH₄, CO₂ – other gases available on request

Meteorological parameters: temperature, pressure and relative humidity

Other parameters: noise, vibration and odour

Location: GPS

The device captures data in real-time and transfers them wirelessly to a advanced web platform, for data analysis and data management, remote control of the equipment and data integration into websites, software and smart city platforms.

Small form stations are light, compact and easy to install within just a few minutes. Once the stations are connected to the Internet through several communication links on-demand (Wi-Fi, 3/4G, LoRa, Zigbee…), the hyper-localised information is automatically transferred to a secure web platform that is accessible 24 hours a day.

Customize your own Small Form AQMS that meets your needs:

Options:

• Integrate sensors that you need
• Choose your communication link
• Add a back-up battery 

Accessories:

• Solar panel and batteries
• Heating resistance
• Mounting plate

For a wide range of applications:

Smart cities, industrial sites, mining sites, sewage treatment plants, mines, soil remediation, refineries, workshops, warehouses, worksites, road networks, race tracks, ski, and sea resorts.

The post TES SMALL FORM AIR QUALITY MONITORING SYSTEMS (AQMS) appeared first on Thomson Environmental Systems.

Typical applications are dynamic situations in the field including:

• Toxic gas monitoring for emergency service personnel
• Monitoring shipping containers
• Soil monitoring.

50 gases can be analyzed at the same time using the supplied touch-screen tablet.

The GT5000 is ideal for on-site measurements of both organic and inorganic compounds at low concentrations in ambient air. Typical applications are industrial hygiene, emergency response and security/border protection.

• Accounts for interferences and can identify unknown compounds
• Can measure 50 gases simultaneously
• Raw data is saved for post analysis
• Library of >200 gases available for measurement and library of 5000+ for identification of unknown gases
• Sub PPM levels possible without pre-concentration ensuring quick response time
• Zero Calibration on clean air or Nitrogen is the only calibration required.
• Weighs just 9.4 kgs
• Internal battery and sample pump inside the backpack unit, makes it easy to carry on in the field.

Gasmet GT5000 can be equipped with customized equipment packages to match the user’s specific needs.

It comes with updated Calcmet software for intuitive measurement in the field – the touch screen tablet is a robust device which can be easily used with and without gloves, or by using a pen.

The new GT5000 Terra is capable of measuring over 300 gases and up to 50 gases simultaneously. It has all the advantages of FTIR technology. It is quick to setup, easy to operate and low total cost-of-ownership.

View Video

Download Specifications

The post GASMET GT5000 Terra FTIR Gas Analyzer appeared first on Thomson Environmental Systems.

The T-I Max CEM analyzer represents the latest advancement in Continuous-Wave Cavity Ring-Down Spectroscopy designed for superior performance and unprecedented speed of response. It is an ideal, proven solution for MATS HCl compliance needs: continuous emissions monitoring of sources, such as cement kilns, power plants, paper mills, and refineries.  T-I Max CEM analyzer can verify concentrations of target compounds with parts-per-billion accuracy, drift-free stability, and virtually immediate response. Easy and intuitive to install, use, and maintain. The modern software enables you to easily configure the analyzer via its touchscreen display and to communicate with virtually any manufacturer’s DAHS. Two units fit into one 19” rack mount. The robust design — free of moving parts — delivers a high mean time between failures (MTBF) and a very low cost of ownership (COO).

Designed for Continuous Emissions Monitoring (CEM), the robust and compact Tiger-i CEM offers:

• Accuracy traceable to the world’s major national reference labs
• Specificity—no interference
• Sub-ppb detection capability
• No periodic sensor replacement/maintenance
• Unprecedented speed of response
• Wide dynamic range

Applications

• CEM Standards Preparation
• Cement Kilns & Paper Mills
• HF Alkylation Unit Emissions
• Power Generation from Fossil Fuels

Download Data Sheet

The post T-I Max CEM appeared first on Thomson Environmental Systems.

Principle

• Continuous, uninterrupted sampling
• Sample is injected into column for separation
• Controlled oven selects optimum temperature based on application
• Detection achieved by a sulphur specific photometric double flame detector

Features

• The double flame ensures no quenching occurs
• Automatic linearisation of compounds
• Identification of compounds is based on their retention time (Elution from the column)
• Automatic data validation as standard with the internal permeation tube

Download Specifications – chroma S

Download Specifications – chroma S – COS

The post Chromatotec Chroma S appeared first on Thomson Environmental Systems.